Application: Metallurgy and Metals

Here below 15 application documents of this product library containing 127 downloadable docs.

CS744 – Carbon and Sulfur Determination in Low Carbon Ferroalloys

Ferroalloys are alloys of iron that contain a high level of one or more additional primary elements.Learn more...

SC832HT SODA LIME GLASS

This method describes the Carbon/Sulfur analysis of soda lime glass with a high temperature tube furnace without accelerator.Learn more...

CS744 BATTERY PASTE

This application note describes the Sulfur analysis of Battery Paste, Lead Oxide and Lead SulfateLearn more...

CS744 SODA LIME GLASS

This method describes the Carbon/Sulfur analysis of soda lime glass with a high frequency furnaceLearn more...

Wire and ROD Analysis with LECO GDS

In this application note some methods are described that allows a perfect analysis of thin and/or long samples like wired and rods.Learn more...

Oxygen and Nitrogen Determination in Refractory Metals and Their Alloys

Oxygen and Nitrogen determination in refractory metals like Titanium, Zirconium and othersLearn more...

Carbon and Sulfur Determination in Limestone/Dolomite

Carbon / Sulfur Determination in CaCO3 / Dolomite/ LimestoneLearn more...

Carbon and Sulfur Determination in Limestone/Dolomite

Carbon / Sulfur Determination in CaCO3 / Dolomite/ LimestoneLearn more...

Performance of GDS to Analyze Grey Iron and Other As-Cast Materials

Glow discharge spectrometry (GDS) is capable of analyzing all types of cast irons while other techniques, especially spark-emission spectrometry, commonly struggle in this area. This capability arises from several features of glow discharge sputtering that decidedly differentiate these techniques.Learn more...

NEW ! Oxygen and Nitrogen in Solid Iron, Steel, Nickel-Base, and Cobalt-Base Alloys

The LECO ON736 provides a cost-effective and efficient means of simultaneously determining the amount of oxygen and nitrogen in steel, nickel-base, and cobalt-base alloys. The following application note outlines the hardware requirements, system settings, and expected performance of this test.Learn more...

Sulfur Determination in Ultra Low Sulfur Steel, Nickel, and Superalloys

The LECO CS844ES with a detection limit of approximately 0.1 μg of sulfur expands the capability of the combustion technique to levels previously limited to GD-MS. The following application note outlines the settings and steps required to determine ultra-low levels of sulfur in steel, nickel, and superalloys.Learn more...

Determination of Carbon and Sulfur in Cast Iron

The following application note outlines the settings and steps required to determine the carbon and sulfur levels in cast iron with the CS/C/S844 series of elemental analyzers. With its simultaneous carbon and sulfur detection capability and easy-to-use touch-screen interface, the CS844 carbon and sulfur by combustion analyzer makes the perfect addition to any foundry laboratory.Learn more...

Determination of Carbon and Sulfur in Fluorspar

Carbon is one of the impurities in fluorspar that must be determined, and can be in the form of carbonates or organic carbon. The LECO CS844, when equipped with the optional halogen trap, provides a fast and accurate means of determining the amount of total carbon in fluorspar, and can be set to automatically calculate the approximate carbon as CaCO3 in the sample. The following application note outlines the sample preparation steps, analytical procedure, and provides examples of typical results.Learn more...

Determination of Surface Carbon on Aluminum Sheets/Rods/Wire

The LECO RC612 is a multiphase carbon and moisture determinator specifically designed to differentiate various forms of carbon by the temperature at which they combust. This capability facilitates the determination of the amount of carbon present on the surface of aluminum sheets or rods, which is relative to the amount of oils or surface modifying treatments.Learn more...

Hardness Profile Determination in Decarburized Steel

With LECO AMH55 automated hardness tester indentations are made and measured automatically. Advanced software features offer fully automated operation : auto stage, indentations, auto focus, auto-measurement, calculate hardness and documenting. Learn more...
Return